If not I assigned a number for the roll and frame if It was not on the slide mount. Many of them are already labeled with a roll number and a frame number so if present I used those. Scan at 2400 dpi saving TIFF files out with automatic numbering according to my defined scheme.Īll the color slides from my parents are RG301. The film may not be Ektachrome but that was the closest to recovering the red shifted slides to something approaching normal colors. I used the film type Kodak, Ektachrome, Color balance auto levels, restore colors on, but no other corrections. Place the slides emulsion side up in the holder as follows Be sure the scanner surface is clean and VueScan is already up with my preset. Take a batch of the 2.25 x2.25 color slides out and clean if necessary. Work flow for color slides has been this: The crop boxes tend to drift, for some reason they are not perfectly saved, but that is not as big a problem as I imagined. Once I had the crop boxes and other parameters as I wanted them I saved the settings in file for re-use later. Then go back and move each one individually to the correct location. So the initial procedure was to select each frame in turn and move the crop boxes into the middle of empty space not touching and with their centers not within the locations where I wanted them to end up. Solving the cropping being wrong involved changing the crop units to pixels and using the up and down arrows on the crop box to move them out of the way so that when I moved one on top of the frame I wanted it didn't match the old crop box I wanted it to replace. This provided a way to line up slides and negatives easily. Not as useful as Victoria's books in terms of really explaining things but at least a whole lot better than the on-line manual.įirst step was to create a fake cardboard carrier that masked out the scanner just like the plastic ones that come with it. First off I purchased this book : "The VueScan Bible: Everything You Need to Know for Perfect Scanning" by Sascha Steinhoff. How do I tell VueScan to ignore the blank frames in each row of frames? My film s usually 4 frames per strip with some one or 2 only. In a related issue, when I set it up to scan 35 mm color negatives VueScan assumes that I have 4 film strips with 6 frames on each strip. I've tried measuring the x y offset by hand and entering it in but it resets to zero.ĭoes anyone have a procedure to set up multiple scans at a specific custom size that will work? Not only do i have to do that for these 2.25 inch ones but I also have to do it for the other odd film sizes so I really need to get this to work. I've tried standard, letting the software try to figure out how to do it and that didn't work either. I've tried automatic cropping and I get 24 individual frames none of which is correct. Well I have been experimenting for over 4 hours with zero useful results! When I asked for assistance from Ed Hamrick the only response was to experiment. I have nearly 500 negatives to scan and if I have to rename them all by hand it’s a huge time cost. I will be saving to a file with automatic numbers for each frame. The correct numbering for these negatives isīut I can’t figure out how to get VueScan to understand that. I can drag the crop to the correct portion of the image and it stays there properly but I just didn’t get a screen shot of it once it was in the correct position. This is how it initially comes up for frame 1. I can’t get the screen shots to both show the numbering and the selection as it’s based on mouse location so when I try to take the screen shot the number on top of the image goes away. No matter what I try in terms of dragging the crop frame to the correct location it won’t stay there and actually renumber them properly. Without that the automatic file naming won’t work properly The numbering goes down then across I need it to go across then down and I thought by using manual I could make it do that but I can’t get it to work. 1st one is fineĬlick on input select frame 2 click on crop drag the selection to image 2 which is to the right of image 1Ĭlick on input and now it’s saying I am at frame 5. Here are the steps I’ve done and the resultsĬlick on input be sure it’s looking at frame 1 click on crop and verify the selection is correct. Initial tests with slides seemed promising so I moved on to attempting to test scanning the 2.25 inch B&W negatives. I'm trying to test using VueScan running my older Epson4870 Photo Scanner for my big project.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |